Swimming Pool Heater
How to Heat Swimming Pool Water
We go down to the swimming pool to relieve fatigue, to keep the body healthy, to exercise, or to swim. And it is either winter season or there are many countries where it is winter or cold for 6 months of the year. The pool water is also cold and no one can swim in the cold water,or swimming cannot be done.
So in order to heating the swimming pool water, the heater has to be fixed in the pool water circulation system.
There are can be many types of heater for heating swimming pool water.
Such as-
Electric heater
Gas heater
Hot steam heater etc.
However, gas and steam heaters should be used in the swimming pool water, electric hester carry the risk of accident.
Equipment of the swimming pool heater
- Coper tube type heater
- Gat valves
- Sensors
- Steam line
- Solenoid valve for steam line
- Solenoid coil
- Ms pipe for steam line
- Pipe feting for steam line
- Pool water pipe feting
- Water flow switch
- Temperature meter
- Control board
- On/off switch
- Magnetics contactor
- Circuits bracer
- 220 voltage power line
How to fox Steam Heater
Heater should be selected according to the volume of swimming pool water. First you have to make the base to fix the heater. The water tub heater with the base has to be fixed properly with nut and bolts.
The heater need to be fixed in the next water line of the swimming pool filtration system. After the filter of the swimming pool, the T fittings should be fixed from the water line and a line should be drawn and fixed in the in lone of the heater. And the water out line of the heater has to be fixed on the other side of the water line of the swimming pool through T fittings with a pipe. Then a gate valve must be fixed between the water in and out line of the heater of the pool water line. And the gate valve must be closed. As if water is flowing though the heater as a bypass.
Then the steam line must be fixed in the in and out line of the heater steam line.
The solenoid valve in the in and out line of the steam line needs to be fixed. And two power coil on two solenoid valve to fix the steam line.
A water flow switch need to be fixed in the in-line of the heater. Because if the water flow in the water line is off, the heater is also off.
The temperature sensor must be fixed in the widdle of the heater and in the in and out line of the heater.
The control board needs to be fixed and the power supply line needs to be fixed. Then the power line of solenoid coil, temperature sensor, water flow switch has to be fixed. And make a connection to the control board. The on and off switch on the control board and the temperature meter need to be fixed. And i have to set the temperature and turn on the heater. The water temperature in the swimming pool is usually between 30 to 32 degrees centigrade. The temperature of the swimming pool water in maintained by turning the heater on and off when the temperature is 30 to 32 degrees centigrade.
The heater need to be fixed in the next water line of the swimming pool filtration system. After the filter of the swimming pool, the T fittings should be fixed from the water line and a line should be drawn and fixed in the in lone of the heater. And the water out line of the heater has to be fixed on the other side of the water line of the swimming pool through T fittings with a pipe. Then a gate valve must be fixed between the water in and out line of the heater of the pool water line. And the gate valve must be closed. As if water is flowing though the heater as a bypass.
Then the steam line must be fixed in the in and out line of the heater steam line.
The solenoid valve in the in and out line of the steam line needs to be fixed. And two power coil on two solenoid valve to fix the steam line.
A water flow switch need to be fixed in the in-line of the heater. Because if the water flow in the water line is off, the heater is also off.
The temperature sensor must be fixed in the widdle of the heater and in the in and out line of the heater.
The control board needs to be fixed and the power supply line needs to be fixed. Then the power line of solenoid coil, temperature sensor, water flow switch has to be fixed. And make a connection to the control board. The on and off switch on the control board and the temperature meter need to be fixed. And i have to set the temperature and turn on the heater. The water temperature in the swimming pool is usually between 30 to 32 degrees centigrade. The temperature of the swimming pool water in maintained by turning the heater on and off when the temperature is 30 to 32 degrees centigrade.
If you need help Please contract us
Call 01687179140.
No comments:
Post a Comment
If you have any doubts, pleas let me know.